Sikkens Cetol WM 675 Clear Isolating Mid Coat

Price Range:£208.90
Price £208.90
This is a required field.
In stock
Next day delivery available

Sikkens Cetol WM 675 is an isolating, highly transparent midcoat coating

Sikkens Cetol WM 675 is the perfect Mid Coat to suit any Sikkens system. Mid coat’s can be used to create better results as part of an optimised system. Surfaces with 2-coat coverage (mid and top coats) are generally treated with the same product for both coats. But in many cases better results are achieved on certain Hard Wood timbers with a product combination which help increase pore filling and prevent the formation of weak points after later weathering and moisture and UV irradiation.

Sikkens Cetol WM 675 is a dipping translucent waterbourne acrylic/alkyd isolating midcoat for exterior joinery constructions.

This mid coat for exterior wooden components comes as a colourless, highly transparent coatings with good isolating properties.

It can be deluged using Dipping or Flow Coating onto a variety of stable wooden components like Windows, Outer Doors, Conservatories and semi-stable wooden components like Rafters, Gates, Shutters and Posts.


Features

  • High Transparency
  • Good Pore Wetting
  • Good isolating Properties
  • Ionen-Lock-Technology

Technical Information

Brand Sikkens
Coverage 6-20 m²/Litre Depending on application method, type and absorption of timber.
Application Dipping, Flow Coating
Drying Time Touch dry in 30 minutes, dry to handle in 4-6 hours @ 23°C
Coats 1 Coats as part of a system
Cleanup Clean with water immediately after use and, if required, add some commercially available washing-up liquid or ST 830.
Storage 2 Year if can kept dry and firmly shut
VOC 50g/l
Ingredients Acrylic
MPN 5115102-70

Documentation

Product Information

Safety Data Sheet


Safety 

Here at AllFinishes we take health and safety seriously and recommend you use the correct protection for the job. Disregarding safety equipment can be damaging and result in long term health conditions. Please check out our Moldex range for high quality respirators and hearing protection.


Preparation

The wood moisture content for the application of Sikkens coating systems should be between 12 % and 15 %. The selected wood, the design and the

applied layer thicknesses must comply with current technical standards.

All horizontal surfaces shall be bevelled by 15 ° and all edges shall be rounded with a radius of at least 2 mm.

Joints and open end grains must be sealed to prevent the ingress of water into the structure.

The substrates must be dry, free from dust and grease.Where appropriate, the wooden articles to be treated must be fully secured (e.g. via tension belts or clamping devices) prior to treatment and during the dipping process, and must not be manually handled until after the treated articles are surface dry.



Application

Dipping, flow-coating. Processing viscosity is approx. 11 seconds in a DIN cup 4 mm or approx.

23 25 seconds in a ISO cup 3 mm at 20 °C material temperature EU-Regulation No. 528/2012: This product must only be used in fully automated dipping processes where all steps in the treatment and drying process are mechanised and no manual handling takes place, including when the treated articles are transported through the dip tank to the draining/drying and storage (if not already surface dry before moving to storage).

Where appropriate, the wooden articles to be treated must be fully secured (e.g. via tension belts or clamping devices) prior to treatment and during the dipping process, and must not be manually handled until after the treated articles are surface dry.


Aftercare

We recommend using the Sikkens Cetol WM 675 in part of the manufacturers recommended system.


Impregnation

Cetol WV 880 BPD


Primer

Cetol WP 566

Rubbol WP 194


Mid coat

Cetol WM 675


Top coat

Cetol WF 952 / WF 957

Rubbol WF 375

Rubbol WF 378 / WF 380

Rubbol WF 382 / WF 387



Product Numbers

Manufacturer's Part Numbers (MPN):
5115102-70


Other

The coating system mentioned here is only an example; other systems are possible. Please refer to the relevant Technical Data Sheets and ask your Allfinishes Technical Representative for advice about coating systems.

All external materials coming into contact with the coating system (e.g. putty, adhesive tapes, sealants, cleaners, etc.) must be tested for compatibility by the user.