AllFinishes Covid-19 Update - Please Read
Please ensure you are selecting all options when adding to your basket
This is a required field.
Price Range:£31.60 - £115.84
Price £31.60
In stock
Jotun Pilot QD Primer

Jotun Pilot QD Primer is a 1K Alkyd zinc phosphate anti-corrosive primer

Jotun Pilot QD Primer is a one component oxidatively drying alkyd coating. It is a fast drying, high build, zinc phosphate pigmented product and can be used as primer or mid coat in atmospheric environments. It is also suitable for properly prepared carbon steel, aluminium and wooden substrates.

Areas of Use

Jotun Pilot QD Primer is the ideal primer for Steel and Aluminium structures in moderate, non aggressive environments and resistant against dry heat up to 120°C. It is an anti-corrosive one component oxidatively drying alkyd coating that is a fast drying, high build, zinc phosphate pigmented product. It will dry to a flat Matt finish when fully cured.

Perfect for use on Bare Steel, Shopprimed Steel, Aluminium substrates and previously Coated Surfaces. In a Protective environment it is suitable for a wide range of industrial structures. In Marine environments it is suitable for engine room, topside, deck and superstructures.


  • Suitable for Steel and Aluminium
  • Available in four colours
  • Single pack product ready to use by spray or brush.
  • Can be used as a mid coat in standard environments
  • Zinc Phosphate Primer

Technical Information

Brand Jotun
Coverage Approximately 4-7.5m2 per litre
Application Airless Spray, Brush or Roller (Small Areas Only)
Drying Time Touch dry in 15 minutes, Dry to recoat 1.5 hours, Fully cured in 1.5 hours @ 23°C

2 Coats

Dry film thickness: 40 - 125 μm
Wet film thickness: 70 - 130 μm

Cleanup Clean directly after using Jotun Thinner No. 7
Storage 2 years if can kept dry and firmly shut, away from direct sunlight
VOC 420g/l
Ingredients Xylene, Ethylbenzene


We take health and safety seriously here at AllFinishes and recommend you use the correct protection for the job. Disregarding safety equipment can be damaging and result in long term health conditions. Please check out our Moldex range for high quality respirators and hearing protection.


To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination.

Substrate                              Minimum                                    Recommended                         
Coated surfaces Clean, dry and undamaged compatible coating (ISO 12944-5 6.1) Clean, dry and undamaged compatible coating (ISO 12944-5 6.1)
Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1)
Aluminium The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the surface and to remove all polish from the surface. Abrasive blast cleaning to achieve a surface profile using approved nonmetallic abrasive media which is suitable to achieve a sharp and angular surface profile.
Wood Clean and dry surface. Surface contamination is to be removed by detergents and fresh water cleaning. Clean and dry surface. Surface contamination is to be removed by detergents and fresh water cleaning.


The product can be applied by

Spray Use airless spray.
Brush Recommended.
Roller May be used, but is not recommended for first coat on bare metal. Care must be taken to achieve the specified dry film thickness.


The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Shelf life at 23 °C 48 month(s).


This product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the work.

Health & Safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Write Your Own Review
You're reviewing:Jotun Pilot QD Primer
Your Rating